The Fundamentals of Plumbing Knowledge for Bathtub Installation
The Fundamentals of Plumbing Knowledge for Bathtub Installation
Blog Article
They are making several good annotation on A Step-by-Step Guide to Installing a Bathtub as a whole in this article in the next paragraphs.
Setting up a bath tub isn't specifically rocket science, but it does need solid plumbing, woodworking, and occasionally, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately challenging project. If the old tub is conveniently accessible, the task can relocate quickly; if you have to open up a wall to remove the old bathtub and place the new tub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will certainly need a helper to move out the old bathtub as well as set in the brand-new one. See to it you have certified on your own for the task and also are comfortable trying it. As opposed to employing a professional to take control of a halfway-completed project, it is much better to take into consideration utilizing one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a brand-new tub in your restroom if you have actually currently gotten a brand-new tub as well as do not need to transform the plan of your previous water system pipes.
Your tools as well as material list must consist of the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of removing the existing faucets can be quite bothersome as a result of the limited accessibility that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the continuing to be water that will certainly originate from the pipelines. Once the supply pipelines have been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new faucets, contrast the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin ensuring that the washing machines remain in location in between the tap as well as the sink. Secure the tap in place with the manufacturer offered backnut. As soon as the tap is securely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The former kind ought to be linked to the tap finishes initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Tub
Utilizing the two wooden boards under its feet, position the bathtub in the required position. The wood boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small factors.
The following objective is to make certain that the tub is leveled all round. This can be achieved by checking the spirit level and readjusting the feet on the bathtub until the spirit level checks out degree.
To install taps, fit all-time low of the furthest adaptable tap connector to the proper supply pipe by making a compression join; then do the same for the other tap.
Switch on the water and also inspect all joints and also new pipework for leakages and tighten them if necessary. Fill the bathtub and additionally examine the overflow outlet and the typical electrical outlet for leaks.
Ultimately, deal with the bath paneling as described in the supplier's instruction manual. Tiling as well as securing around the tub needs to wait until the bath tub has been made use of a minimum of when as this will settle it right into its last setting.
Getting ready for the Setup
First of all, the sustaining frame provided with the bath ought to be fitted (if called for) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you use all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its final position.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a stiff seal, creating the water to penetrate the wall in between the bath and the tiling, resulting in difficulties with moisture as well as possible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your fixtures as well as fittings. They are sold in tubes and cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill up the bath tub with water prior to sealing, to permit the motion experienced when the bathtub remains in usage. The sealer can break fairly very early if you do not consider this activity before securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly available on the market. It is suggested to fit the floor tiles making use of waterproof or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid person who reads about Installing A Bathtub, I think sharing that piece of writing was smart. If you enjoyed reading our page if you please don't forget to share it. I praise you for your time. Visit us again soon.
Trusted help? Ring now. Report this page